Control and Reaction States
3 min read · Energy Atlas Editorial
The chain fission reaction in a nuclear reactor is controlled by the neutron absorber content. The reactor can be subcritical, critical, or supercritical.
A fission chain reaction can develop in uranium under suitable conditions. If the neutron population is not appropriately controlled, the chain reaction may either die out or increase. Under certain conditions, such as those created in a nuclear weapon, it can increase extremely rapidly.
In nuclear reactors, the chain reaction must be carefully controlled so that the reactor can be started up, operated at the required power level, adjusted in power and shut down safely. The rate of fission depends on the neutron population in the reactor core. The chain reaction can therefore be controlled by adjusting neutron absorption, for example by inserting or withdrawing control rods containing neutron-absorbing materials. According to the behaviour of the neutron population, a reactor can be in one of three states: subcritical, critical or supercritical.
Video: Subcritical state of a fission chain reaction.
Subcritical
In the subcritical state (k_eff < 1), each generation of fissions produces fewer neutrons that cause further fissions than the preceding generation. The neutron population therefore decreases and a self-sustaining chain reaction cannot be maintained. A reactor becomes subcritical during shutdown, for example when neutron-absorbing control rods are inserted sufficiently far into the core.
Video: Critical state of the nuclear reaction.
Critical
In the critical state (k_eff = 1), each generation of fissions produces, on average, enough neutrons to cause the same number of fission in the next generation. The neutron population and fission rate therefore remain constant. This is the normal state of a nuclear reactor operating at a steady power level.
Video: Supercritical state of a fission chain reaction.
Supercritical
In the supercritical state (k_eff > 1), each generation of fissions produces more neutrons that cause further fissions than the preceding generation. The neutron population and reactor power therefore increase. A controlled slightly supercritical state is used during reactor startup and when increasing the reactor power level. In normal reactor operation, power changes are kept slow enough to remain controllable, largely thanks to the small fraction of delayed neutrons emitted by fissions products.
About two billion years ago, natural self-sustaining fission chain reactions occurred in uranium deposits at Oklo in present-day Gabon. Groundwater acted as a neutron moderator, and changes in the amount of water in the deposits probably caused the natural reactors to operate intermittently.
Keep reading
Articles
Principle of Operation
The binding energy that holds nucleons together is different for each isotope. When fusing light nuclei or splitting heavy nuclei, energy is released.
3 min read
Types of Nuclear Reactions
Nuclear reactions can lead to scattering, capture, or splitting depending on neutron velocity. So-called "slow" neutrons (0.02 eV) can split 235U nuclei.
3 min read
Fission Chain Reaction
When a neutron splits the 235U nucleus, 2-3 neutrons are released. The fission chain reaction occurs when they split other nuclei, releasing more neutrons.
3 min read
Moderator
To increase the chance of fission, the moderator slows down neutrons by collisions. The usual moderators are water, heavy water, and graphite.
3 min read
Absorber
The absorber (boron, cadmium) captures the neutrons and thus regulates the nuclear reactor output. It can be part of the coolant or control rods.
3 min read
Coolant
The coolant removes heat from the fission reaction. The most commonly used is water, but also helium, CO2, molten sodium, lead, or fluoride salts are used.
3 min read
Fission Products
After fission, the uranium nucleus decays into two approximately equal halves. Typical products are iodine and cesium, but other ways of decay exist.
3 min read
The Largest Nuclear Power Plants
In 2012, there were 436 reactors in use worldwide. The largest nuclear power plant is Japan's Kashiwazaki Kariwa with 7,965 MW of installed power output.
3 min read
Questions
How does a nuclear reactor generate electricity?
Fission heat raises steam. A turbine-generator does what it does in any thermal plant.